Nemesis is a full-analogic, linear and solid-state, high precision, high speed, high damping, high feedback and high efficiency class AB audio power amplifier, designed and produced in Italy.
Born from the research of the KRIEG Audio Department to create an amplifier without compromises and with an excellent, perfectly symmetrical, structure: the best electronic and audio performance, in a little board.
Its structure, perfectly symmetrical, is made up of 34 transistors, which grants:
- High precision and low fundamental, intermodulation and thermal (memory) distortion.
- High slew rate and precision on high frequencies.
- High damping factor and precision on low frequencies.
- Very low noise and high signal-to-noise ratio.
- Very low DC output offset.
- High bandwidth.
- High power supply rejection ratio.
- High common mode rejection ratio.
- Total invariability of performance as the load varies.
- Total thermal stability.
- Total high frequencies stability.
- Total stability on capacitive loads.
- Total invariability of bandwidth.
- High open loop gain.
- High efficiency.
- No need for quiescent current (bias) regulation.
In the world of audio, high fidelity is not something subjective, but objective. High fidelity lies in being able to reproduce a song with the utmost precision, as it was recorded. The Nemesis, is a totally neutral amplifier, created for the purpose.
Nemesis is not only the Greek goddess of vengeance but, first of all, of compensation and balance.
The basic idea is that every discrete component is imperfect, however well it can be done or its tolerances are low. If the discrete components were perfect, only one transistor would be enough to produce a totally precise power amplifier. Hence the Nemesis is born, a high precision, high speed and high efficiency class AB analog audio amplifier.
The final concept is easy: if you have to select components to reach a result, then with the slightest variation in temperature, voltage or other variables, the result itself will vary. In audio it is not so much achieving a low amount of distortion that is the problem, but also keeping it while running music, with variations of all genres. And this, an amplifier with few transistors simply cannot guarantee it.
The Nemesis VERSION 2 introduce a new method of controlling the current through the voltage amplifier stage: reducing that necessary and making it more constant. In addition, the capacitors for its own power supply are mounted directly on the board: thus eliminating the need for capacitors at the output of the power supply and reducing the overall size of the case and costs.
Specs
Parameter | Value | Unit |
---|---|---|
Amplifier class | AB | |
Operation method | Single ended (the load is connected between the output and the ground) | |
Supply voltage type | dual voltage | |
Minimum supply voltage | +5, 0, -5 | Vdc |
Recommended supply voltage | +30, 0, -30 | Vdc |
Maximum supply voltage | +50, 0, -50 | Vdc |
Program power (on all load impedances) | 100 | W |
Maximum power (on all load impedances) | 200 | W |
Standby power | 2 | W |
Minimum raccomended supply current | 5 | A |
Output gain | + 27 | dB |
Minumum efficiency | 50 | % |
Maximum efficiency | 94 | % |
Minimum load impedance | 0.5 | Ohm |
Nominal output current (+10Vdc, -10Vdc supply) | 15 | A |
Nominal output current (+30Vdc, -30Vdc supply) | 7 | A |
Nominal output current (+50Vdc, -50Vdc supply) | 4 | A |
THD+N @ 1kHz | 8 Ohm | 100W | 0.005 | % |
IMD THD | 8 Ohm | 100W | 0.007 | % |
Slew rate | 60 | V/us |
Damping factor @ 60 Hz | 8 Ohm | 4000 | |
Output impedance @ 60 Hz | 8 Ohm | 0.002 | Ohm |
Input impedance | 10 | kOhm |
Bandwidth (-3dB) | DC - 1 | MHz |
Audio bandwidth linearity | +- 0.01 | dB |
SNR (non A-weight) @ 1kHz - 100W | 98 | dB |
SNR (A-weight) @ 1kHz - 100W | 108 | dB |
CMRR @ 1kHz | 116 | dB |
PSRR @ 1kHz | 115 | dB |
Open loop gain | 95 | dB |
On-board total capacitance | 13000 | uF |
Board dimensions | 84 (H) x 127 (W) | mm |